tsmgguy

Doesn't look like an M1903 barrel star gauge, either.

B3222 photo #12 shows the bayonet rivet. These were never serial numbered by the factory or the Marine Corps.

Yeah, I ordered a repro M1941 butt stock from Murray's. He sent a beautiful piece of wood that had the correct exterior dimensions. It was not inletted and was therefore useless as I lack the skills necessary to complete the job. Murray explained that he didn't have an original stock to use as a template. A full refund was eventually made, but I never did figure out the object of that exercise. I was out shipping in both directions.

Welcome! The magazine cover spring should be a leaf of spring steel rather than the coil spring shown in your photo, It's part number 31 in the schematic and list shown here: Johnson Semi-Auto 1941 Schematic | Numrich (gunpartscorp.com)

RARE ORIGINAL WW2 M1941 JOHNSON SEMI AUTOMATIC RIFLE MAGAZINE AXIS PIN WWII | eBay I have bought from this seller before and have found them to be honest and diligent. Looks like the flared end of this pin might be slightly bent but that might be a trick of the camera angle.

Looks like a stock lamination is about to separate, too.

Couldn't find it. A link would be helpful.

I'd think that the recontoured receiver would pretty much preclude a restoration to the original configuration.

This rifle shows none of the typical Marine front and rear sight mods. It doesn't look like a gun that saw hard service in the South Pacific.

"New old stock condition" my foot. Thanks!

Very entertaining and informative video linked below. https://www.youtube.com/embed/9uXrWAR6GgE

I don't think this is about the accuracy of the details. Rather, it's about one man's journey to a greater understanding of a classic design. His gunsmithing experience of many years aids him in this. I learned a few things, too. For instance, after owning and shooting a JSAR for the last 30 years or so, I didn't realize that the safety locks both the trigger and the bolt.

Old thread, I know. Here's a pic of these stock markings found on the internet.

If your rifle is doing this look first to the recoil spring. The action should cycle gently, almost as an afterthought, dropping brass just a few feet to the shooters right. It should not be flinging dented brass to the far right of the firing line. Worn guns will cycle violently, too, causing excessive felt recoil and further battering the internals.

I shoot mine (occasionally) with full power Danish M2 ball from the early 1960s. Perfect functioning, and no problems.

Question for you guys with knowledge of Winfield sporters. I notice that on these the recoil spring housing tube stop screw holes are usually filled in on the butt stock. Is the stop usually present under the plug, or is the spring tube held in place only by wood contact and the butt plate?

Are both pins serial numbered? The spare pin/collar/spring assembly in my collection is numbered H2039 and is most like the lower in your photo. I see no evidence or welding or brazing, just some bright metal where the shank was evidently milled to length. The collar wiggles slightly, and doesn't seem to be brazed in place.

Thanks!

My B series JSAR butt stock had what appears to be two small stamps on the flat inside of the magazine swell area. They are a capital A (or upside-down V) and the number 4, each about 1/8 inch in height. Any idea what these signify? The assembler's initials, perhaps? Thanks!

Photo found on the internet while doing a search for "M1941 Johnson Rifle butt stock":

Just a few pics of a gun that I've owned for almost thirty years now. It has almost all of its original finish and a mirror bore. The butt stock was heavily damaged along the comb, so the stock is a John Darling reproduction. Remember him? The stock looks the part as the grain has stood up with time. The sling and bayonet scabbard are repros, but the bayonet is original.

...after field stripping. Hello, Went to reassemble as normal after field strip and the extractor fell into the rotary magazine. No problem getting it out, but when I slid the bolt back into the receiver, the bolt jammed in a forward position and will not budge except to move slightly forward and backward. It seems to be jammed just forward of where it would be in battery. Gentle tapping with a mallet and wooden dowel gets no movement. The bolt cannot be drawn out of the receiver. Insights appreciated! Thanks! Update: No problem! The bolt was hanging up on the ejector.

Thanks!

Hello, all, Is there any way to tell whether the buffer assembly is present in my assembled M1941 rifle? I'd like to avoid taking the end cap off of the recoil spring tube to check. I notice that if I remove the butt plate and stick a piece of stiff wire in the hole in the center of the plug, the wire goes in and stops after a couple of inches or so. Also, looking through the tiny hole in the end cap with a bright light, I can see spring coils that go all the way to the interior end of the cap. Thanks much, Howard

What is the title of Bruce's new book?